# 95 dakota gasifier construction almost complete
**URL:** http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550
**Category:** General Discussion
**Created:** [November 2, 2017, 10:17pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550 "2017-11-02T22:17:51Z")
**Posts on this page:** 20
**Page:** 1
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 2, 2017, 10:17pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/1 "2017-11-02T22:17:52Z")
As I am welding the internal component of the large heat exchanger I am having trouble getting it to test watertight. My question for you all is which parts must be watertight in order to prevent explosions, and which parts can be close enough? For example I’ve heard Wayne say that the spray paint will help to fill up any tiny pin holes. But a hole in the wrong place could blow bigger holes in the system.
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 2, 2017, 10:21pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/2 "2017-11-02T22:21:06Z")
---
### Author:  [@Wayne](http://forum.driveonwood.com/u/Wayne)
#### Post date: [November 3, 2017, 12:12am UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/3 "2017-11-03T00:12:40Z")
Hello amurphyone
If water is just seeping I wouldn’t worry to much about it. Also you may be able to spray some heat resistant paint on the inside and outside of the heat exchanger to help seal it.
I don’t think a very small leak on the heat X would cause an explosion but it may dilute the gas but might not be enough to be noticed .
If the heat X reaches the ignition temperature of the gas it is likely a small flame will form at the point of the leak which would weaken the gas and raise the gas temp going to the cooling rails. Again , it might not be enough to be noticed just depends on the size of the leak .
After the gasifier has been used for a while you will be able to look down in the housing and see if any air leaks have fired up . The heat X should be covered with black soot . If a pen hole has formed and gotten hot enough to catch fire it will be white in that area .
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 3, 2017, 11:03pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/4 "2017-11-03T23:03:08Z")
thank you wayne for responding 2 my question. And thank you for putting together this gasifier design. I am enjoying building it, after painting the heat exchanger I attached it’s outside housing to the outside housing of the fire tube. Things are going great.
---
### Author:  [@Bobmac](http://forum.driveonwood.com/u/Bobmac)
#### Post date: [November 4, 2017, 1:27am UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/5 "2017-11-04T01:27:22Z")
Looking good Amurphyone. Remember, the nice looking black paint on your gasifier will soon be matching the tar and soot, that will be getting on it and that is good. That’s why Wayne decided to paint his WK’s all black, and the rest of us have follow his good and sound proven idea. There are those who prefer stainless steel, but we don’t hold that against him. Lol… I even have some stainless in my build, but you can’t see it.
You will soon to be making a big SWEM going down the road.
Bob
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 6, 2017, 12:23am UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/6 "2017-11-06T00:23:54Z")
Thanks Bob. I chose a black truck so it hopefully all blends together as others have done.
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 12, 2017, 3:00pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/7 "2017-11-12T15:00:54Z")
I have a new concern as I’m getting close to finishing the plumbing of my 95 Dakota gasifier. It’s this: can I use soft rubber tees or will they collapse under vacuum (before and after the hay filter)?
---
### Author:  [@Handy\_Andy](http://forum.driveonwood.com/u/Handy_Andy)
#### Post date: [November 12, 2017, 3:42pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/8 "2017-11-12T15:42:47Z")
I think you should be fine with those rubber tee’s, but to be sure you could rig a test with a hand vacuum pump and one of your gauges.
---
### Author:  [@Wayne](http://forum.driveonwood.com/u/Wayne)
#### Post date: [November 12, 2017, 3:56pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/9 "2017-11-12T15:56:38Z")
Hello Aaron .
I think the rubber Ts would be OK as long as they are in the system where there will be little heat . Anywhere that pvc is used I think they would hold up.
I used some rubber Ls on my hopper tubes and after time they began to collapse . The temps in this area occasionally would rise to around 250-300 F.
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 15, 2017, 3:55pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/10 "2017-11-15T15:55:37Z")
Ok. Thank you. I have tried to minimize large rubber couplers like elbows and tees.
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 18, 2017, 9:43pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/11 "2017-11-18T21:43:08Z")
Problem: i wired up a cheap aftermarket ford headlight switch/dimmer and hooked it up to the green wire with black on the Dakota. When I turn on the rotary potentiometer the coil analog dimmer coil burns to glowing hot. It operates as planned slowing the fuel pump down…but if I leave it on for more than 5 Seconds it will burn itself out. Can anyone recommend a dimmer switch that may work better for this truck?
Thanks
Aaron
---
### Author:  [@Wayne](http://forum.driveonwood.com/u/Wayne)
#### Post date: [November 18, 2017, 11:18pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/12 "2017-11-18T23:18:43Z")
Hello Aaron .
I am using the headlight switch / dimmer but when I use it it is either all the way on or all the way off , bypassing the rheostat. The exception is I use the rheostat to give the truck just a little gasoline while stating up. I never leave the current running though the rheostat more than 2-3 sec at a time and keep my hand on the knob while giving it a little gasoline so as not to forget and leave the current on the rheostat .
If I need to hybrid drive I turn the switch on full and let the truck computer take over .
In my dodge ram I am using a ford headlight switch from a junk truck from the late 60s. I have about 5-6 years of driving on it with no problem .
All my other vehicles I have used the headlight switch form a junk dakota ( mid 90s) . I have had only one to go bad and my son was doing the driving when this happen.
---
### Author:  [@Carl](http://forum.driveonwood.com/u/Carl)
#### Post date: [November 19, 2017, 12:08am UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/13 "2017-11-19T00:08:52Z")
Hi Aaron,
The Reese Towpower 74642 Brakeman Compact Brake Controller is the easiest to start with. It is heavy duty. This will get you there: [http://forum.driveonwood.com/t/pwm-fuel-pump-controllers/1111](http://forum.driveonwood.com/t/pwm-fuel-pump-controllers/1111) scroll down to the second entry. We’ll help if you have more questions.
---
### Author:  [@trigaux](http://forum.driveonwood.com/u/trigaux)
#### Post date: [November 19, 2017, 3:10am UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/14 "2017-11-19T03:10:51Z")
my bad
error 20 letters
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 19, 2017, 2:52pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/15 "2017-11-19T14:52:42Z")
Would something like this work too? It says its PWM…
LED Dimmer PWM DC Lighting Dimmer Controller for LED Incandescent Auto RV Marine Aircraft Interior Lighting [https://www.amazon.com/dp/B001CM74R2/ref=cm\_sw\_r\_cp\_apa\_BPzeAb56FR4D9](https://www.amazon.com/dp/B001CM74R2/ref=cm_sw_r_cp_apa_BPzeAb56FR4D9)
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 19, 2017, 2:53pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/16 "2017-11-19T14:53:36Z")
Thank you Wayne. I will just use it like an on-off switch until I figure out something heavier-duty 4 hybrid driving.
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 19, 2017, 3:03pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/17 "2017-11-19T15:03:10Z")
Thanks Carl. I will consider modifying a hauler brake!
---
### Author:  [@trikebuilder57](http://forum.driveonwood.com/u/trikebuilder57)
#### Post date: [November 19, 2017, 3:52pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/18 "2017-11-19T15:52:30Z")
This is one I just bought; [https://www.ebay.com/itm/400W-DC-10V-40V-10A-PWM-New-Motor](https://www.ebay.com/itm/400W-DC-10V-40V-10A-PWM-New-Motor)
---
### Author:  [@mggibb](http://forum.driveonwood.com/u/mggibb)
#### Post date: [November 19, 2017, 5:02pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/19 "2017-11-19T17:02:09Z")
I agree with Al. Mine has worked flawlessly for almost 3 years and 7000. Miles
I like the price also
---
### Author:  [@amurphyone](http://forum.driveonwood.com/u/amurphyone)
#### Post date: [November 22, 2017, 2:10pm UTC](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550/20 "2017-11-22T14:10:49Z")
Al and Micheal,
These PWM units look perfect and more of a dedicated use than the trailer breaking device.
Aaron
[Next page](http://forum.driveonwood.com/t/95-dakota-gasifier-construction-almost-complete/3550.md?page=2)