# When to say good enough...?
**URL:** http://forum.driveonwood.com/t/when-to-say-good-enough/1218
**Category:** General Discussion
**Created:** [August 15, 2014, 4:58pm UTC](http://forum.driveonwood.com/t/when-to-say-good-enough/1218 "2014-08-15T16:58:23Z")
**Posts on this page:** 5
**Page:** 1
### Author:  [@tritowns](http://forum.driveonwood.com/u/tritowns)
#### Post date: [August 15, 2014, 4:58pm UTC](http://forum.driveonwood.com/t/when-to-say-good-enough/1218/1 "2014-08-15T16:58:23Z")
Just thinking about the stuff I’m doing…
I’m at the stage where I pressure test my internal air preheat parts… I usually button stuff up as well as I can and then hook up the air compressor, pressurize the system and use soapy water to find any pin holes… I typically set the regulator on the compressor at around 20psi… today I forgot to and it was set at it’s maximum of about 130psi…
I did have 3 tiny tiny pin holes… which I promptly welded up… it is still kinda leaky as the nozzles arn’t screwed down tight (haven’t been drilled yet) but for the most part I suspect it still was around 100 psi internal pressures…
I’m gonna call that a successful test…
But my thoughts are here, when is something good enough?
What kinda test are others using to see how tight their builds are?
Feel free to comment as this could be useful to new people here that are in the process of getting their feet wet with a build
Arvid
---
### Author:  [@bboes](http://forum.driveonwood.com/u/bboes)
#### Post date: [August 15, 2014, 5:05pm UTC](http://forum.driveonwood.com/t/when-to-say-good-enough/1218/2 "2014-08-15T17:05:22Z")
Petrochemical industry standard is to test and hold at 1.5 times design pressure for 15 minutes, and usually design is around twice operating pressure. Applying that to our gasifiers, let’s say we’re pulling a max 50 inches water column while operating. So if it’ll hold 150 inches (5.4psig) for 15 minutes I’d say you’re doing good!
---
### Author:  [@ook187](http://forum.driveonwood.com/u/ook187)
#### Post date: [August 15, 2014, 10:34pm UTC](http://forum.driveonwood.com/t/when-to-say-good-enough/1218/3 "2014-08-15T22:34:10Z")
HA HA … Billy, your setup in Kansas was one of the best I’ve ever seen. It’s an honor !!! Mike
---
### Author:  [@bboes](http://forum.driveonwood.com/u/bboes)
#### Post date: [August 16, 2014, 6:57am UTC](http://forum.driveonwood.com/t/when-to-say-good-enough/1218/4 "2014-08-16T06:57:39Z")
Hey MikeL! The best you’ve seen? You must have been looking at Wayne’s setup instead of mine! That, or the heat was getting to ya! Man, was it a scorcher that weekend. That gasifier I brought was my first flux core welding project, and I’m convinced more weld bead was ground off than stayed on! After much cussing, grinding and rewelding, it finally held water. Here’s a short clip from my first gasifier showing plenty of drips and gas leaks:
[ ](https://www.youtube.com/watch?v=0TCjoGE84_I)
---
### Author:  [@Wayne](http://forum.driveonwood.com/u/Wayne)
#### Post date: [August 16, 2014, 12:32pm UTC](http://forum.driveonwood.com/t/when-to-say-good-enough/1218/5 "2014-08-16T12:32:45Z")
Good morning Arvid . Thanks for the post .
Wow !! That was some test . I can’t match that !!
My testing is usually with water and will depend on what part of the gasifier .
There are certain parts that I make sure there are NO leaks Some parts a very small pen hole would be OK .
BBB